Internet Engineering Task Force (IETF)                       B. Liu, Ed.
Request for Comments: 8196                           Huawei Technologies
Category: Standards Track                                    L. Ginsberg
ISSN: 2070-1721                                            Cisco Systems
                                                             B. Decraene
                                                                  Orange
                                                               I. Farrer
                                                     Deutsche Telekom AG
                                                          M. Abrahamsson
                                                               T-Systems
                                                               July 2017


                        IS-IS Autoconfiguration

Abstract

   This document specifies IS-IS autoconfiguration mechanisms.  The key
   components are IS-IS System ID self-generation, duplication
   detection, and duplication resolution.  These mechanisms provide
   limited IS-IS functions and are therefore suitable for networks where
   plug-and-play configuration is expected.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc8196.















Liu, et al.                  Standards Track                    [Page 1]


RFC 8196                 IS-IS Autoconfiguration               July 2017


Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Protocol Specification  . . . . . . . . . . . . . . . . . . .   4
     3.1.  IS-IS Default Configuration . . . . . . . . . . . . . . .   4
     3.2.  IS-IS NET Generation  . . . . . . . . . . . . . . . . . .   4
     3.3.  Router-Fingerprint TLV  . . . . . . . . . . . . . . . . .   6
     3.4.  Protocol Operation  . . . . . . . . . . . . . . . . . . .   7
       3.4.1.  Startup Mode  . . . . . . . . . . . . . . . . . . . .   7
       3.4.2.  Adjacency Formation . . . . . . . . . . . . . . . . .   8
       3.4.3.  IS-IS System ID Duplication Detection . . . . . . . .   8
       3.4.4.  Duplicate System ID Resolution Procedures . . . . . .   8
       3.4.5.  System ID and Router-Fingerprint Generation
               Considerations  . . . . . . . . . . . . . . . . . . .   9
       3.4.6.  Duplication of Both System ID and Router-Fingerprint   10
     3.5.  Additional IS-IS TLVs Usage Guidelines  . . . . . . . . .  12
       3.5.1.  Authentication TLV  . . . . . . . . . . . . . . . . .  12
       3.5.2.  Metric Used in Reachability TLVs  . . . . . . . . . .  12
       3.5.3.  Dynamic Name TLV  . . . . . . . . . . . . . . . . . .  12
   4.  Security Considerations . . . . . . . . . . . . . . . . . . .  12
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  13
   6.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  13
     6.1.  Normative References  . . . . . . . . . . . . . . . . . .  13
     6.2.  Informative References  . . . . . . . . . . . . . . . . .  14
   Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . . .  14
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  15








Liu, et al.                  Standards Track                    [Page 2]


RFC 8196                 IS-IS Autoconfiguration               July 2017


1.  Introduction

   This document specifies mechanisms for IS-IS [RFC1195] [ISO_IEC10589]
   [RFC5308] to be autoconfiguring.  Such mechanisms could reduce the
   management burden for configuring a network, especially where plug-
   and-play device configuration is required.

   IS-IS autoconfiguration is comprised of the following functions:

   1.  IS-IS default configuration

   2.  IS-IS System ID self-generation

   3.  System ID duplication detection and resolution

   4.  IS-IS TLV utilization (authentication TLV, metrics in
       reachability advertisements, and Dynamic Name TLV)

   This document also defines mechanisms to prevent the unintentional
   interoperation of autoconfigured routers with non-autoconfigured
   routers.  See Section 3.3.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.  When these words are not in ALL CAPS (such
   as "should" or "Should"), they have their usual English meanings and
   are not to be interpreted as [RFC2119] key words.

2.  Scope

   The autoconfiguration mechanisms support both IPv4 and IPv6
   deployments.

   These autoconfiguration mechanisms aim to cover simple deployment
   cases.  The following important features are not supported:

   o  multiple IS-IS instances

   o  multi-area and level-2 routing

   o  interworking with other routing protocols






Liu, et al.                  Standards Track                    [Page 3]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   IS-IS autoconfiguration is primarily intended for use in small (i.e.,
   10s of devices) and unmanaged deployments.  It allows IS-IS to be
   used without the need for any configuration by the user.  It is not
   recommended for larger deployments.

3.  Protocol Specification

3.1.  IS-IS Default Configuration

   This section defines the default configuration for an autoconfigured
   router.

   o  IS-IS interfaces MUST be autoconfigured to an interface type
      corresponding to their Layer 2 capability.  For example, Ethernet
      interfaces will be autoconfigured as broadcast networks and Point-
      to-Point Protocol (PPP) interfaces will be autoconfigured as
      Point-to-Point interfaces.

   o  IS-IS autoconfiguration instances MUST be configured as level-1 so
      that the interfaces operate as level-1 only.

   o  originatingLSPBufferSize is set to 512.

   o  MaxAreaAddresses is set to 3.

   o  Extended IS reachability (TLV 22) and IP reachability (TLV 135)
      TLVs [RFC5305] MUST be used, i.e., a router operating in
      autoconfiguration mode MUST NOT use any of the following TLVs:

      *  IIS Neighbors (TLV 2)

      *  IP Int. Reach (TLV 128)

      *  IP Ext. Address (TLV 130)

      The TLVs listed above MUST be ignored on receipt.

3.2.  IS-IS NET Generation

   In IS-IS, a router (known as an Intermediate System) is identified by
   a Network Entity Title (NET), which is a type of Network Service
   Access Point (NSAP).  The NET is the address of an instance of the
   IS-IS protocol running on an IS.








Liu, et al.                  Standards Track                    [Page 4]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   The autoconfiguration mechanism generates the IS-IS NET as the
   following:

   o  Area address

         In IS-IS autoconfiguration, this field MUST be 13 octets long
         and set to all 0s.

   o  System ID

         This field follows the area address field and is 6 octets in
         length.  There are two basic requirements for the System ID
         generation:

         -  As specified by the IS-IS protocol, this field must be
            unique among all routers in the same area.

         -  After its initial generation, the System ID SHOULD remain
            stable.  Changes such as interface enable/disable, interface
            connect/disconnect, device reboot, firmware update, or
            configuration changes SHOULD NOT cause the System ID to
            change.  System ID change as part of the System ID collision
            resolution process MUST be supported.  Implementations
            SHOULD allow the System ID to be cleared by a user-initiated
            system reset.

         More specific considerations for System ID generation are
         described in Section 3.4.5.























Liu, et al.                  Standards Track                    [Page 5]


RFC 8196                 IS-IS Autoconfiguration               July 2017


3.3.  Router-Fingerprint TLV

   The Router-Fingerprint TLV is similar to the Router-Hardware-
   Fingerprint TLV defined in [RFC7503].  However, the TLV defined here
   includes a Flags field to support indicating that the router is in
   startup mode and is operating in autoconfiguration mode.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |    Length     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  Flags        |                                               |
      +-+-+-+-+-+-+-+-+        Router-Fingerprint (Variable)          .
      .                                                               .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type: 15.

   Length:  The length, in octets, of the "Flags" and "Router-
         Fingerprint" fields.

   Flags:  1 octet.

                               0 1 2 3 4 5 6 7
                              +-+-+-+-+-+-+-+-+
                              |S|A| Reserved  |
                              +-+-+-+-+-+-+-+-+

   S flag:  When set, indicates the router is in "startup" mode.

   A flag:  When set, indicates that the router is operating in
         autoconfiguration mode.  The purpose of the flag is so that two
         routers can identify if they are both using autoconfiguration.
         If the A flag setting does not match in hellos, then no
         adjacency should be formed.

   Reserved:  These flags MUST be set to zero and MUST be ignored by the
         receiver.

   Router-Fingerprint:  32 or more octets.

   More specific considerations for Router-Fingerprint are described in
   Section 3.4.5.






Liu, et al.                  Standards Track                    [Page 6]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   The Router-Fingerprint TLV with the A flag set MUST be included in
   IS-IS Hellos (IIHs) originated by a router operating in
   autoconfiguration mode.  An autoconfiguration mode router MUST ignore
   IIHs that don't contain the Router-Fingerprint TLV with the A flag
   set.

   The Router-Fingerprint TLV with the A flag set MUST be included in
   Link State PDU (LSP) #0 originated by a router operating in
   autoconfiguration mode.  If an LSP #0 is received by a router
   operating in autoconfiguration mode and the LSP either does NOT
   contain a Router-Fingerprint TLV or it does contain a Router-
   Fingerprint TLV but the A flag is NOT set, then the LSP is flooded as
   normal, but the entire LSP set originated by the sending router MUST
   be ignored when running the Decision Process.

   The Router-Fingerprint TLV MUST NOT be included in an LSP with a non-
   zero number and when received MUST be ignored.

3.4.  Protocol Operation

   This section describes the operation of a router supporting
   autoconfiguration mode.

3.4.1.  Startup Mode

   When a router starts operation in autoconfiguration mode, both the S
   and A flags MUST be set in the Router-Fingerprint TLV included in
   both hellos and LSP #0.  During this mode, only LSP #0 is generated
   and IS or IP/IPv6 reachability TLVs MUST NOT be included in LSP #0.
   A router remains in startup mode for a minimum period of time
   (recommended to be 1 minute).  This time should be sufficient to
   bring up adjacencies to all expected neighbors.  A router leaves
   startup mode once the minimum time has elapsed and full LSP database
   synchronization is achieved with all neighbors in the UP state.

   When a router exits startup mode, it clears the S flag in Router-
   Fingerprint TLVs that it sends in hellos and LSP #0.  The router MAY
   now advertise the IS neighbor and IP/IPv6 prefix reachability in its
   LSPs and MAY generate LSPs with a non-zero number.

   The purpose of startup mode is to minimize the occurrence of System
   ID changes for a router once it has become fully operational.  Any
   System ID change during startup mode will have minimal impact on a
   running network because, while in startup mode, the router is not yet
   being used for forwarding traffic.






Liu, et al.                  Standards Track                    [Page 7]


RFC 8196                 IS-IS Autoconfiguration               July 2017


3.4.2.  Adjacency Formation

   Routers operating in autoconfiguration mode MUST NOT form adjacencies
   with routers that are NOT operating in autoconfiguration mode.  The
   presence of the Router-Fingerprint TLV with the A flag set indicates
   the router is operating in autoconfiguration mode.

   NOTE: The use of the special area address of all 0s makes it unlikely
   that a router that is not operating in autoconfiguration mode will be
   in the same area as a router operating in autoconfiguration mode.
   However, the check for the Router-Fingerprint TLV with the A flag set
   provides additional protection.

3.4.3.  IS-IS System ID Duplication Detection

   The System ID of each node MUST be unique.  As described in
   Section 3.4.5, the System ID is generated based on entropies (e.g.,
   Media Access Control (MAC) address) that are generally expected to be
   unique.  However, since there may be limitations to the available
   entropies, there is still the possibility of System ID duplication.
   This section defines how IS-IS detects and resolves System ID
   duplication.  A duplicate system ID may occur between neighbors or
   between routers in the same area that are not neighbors.

   A duplicate system ID with a neighbor is detected when the System ID
   received in an IIH is identical to the local System ID and the
   Router-Fingerprint in the received Router-Fingerprint TLV does NOT
   match the locally generated Router-Fingerprint.

   A duplicate system ID with a non-neighbor is detected when an LSP #0
   is received, the System ID of the originator is identical to the
   local System ID, and the Router-Fingerprint in the Router-Fingerprint
   TLV does NOT match the locally generated Router-Fingerprint.

3.4.4.  Duplicate System ID Resolution Procedures

   When a duplicate system ID is detected, one of the systems MUST
   assign itself a different System ID and perform a protocol restart.
   The resolution procedure attempts to minimize disruption to a running
   network by choosing, whenever possible, to restart a router that is
   in startup mode.

   The contents of the Router-Fingerprint TLVs for the two routers with
   duplicate system IDs are compared.







Liu, et al.                  Standards Track                    [Page 8]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   If one TLV has the S flag set (the router is in startup mode) and one
   TLV has the S flag clear (the router is NOT in startup mode), the
   router in startup mode MUST generate a new System ID and restart the
   protocol.

   If both TLVs have the S flag set (both routers are in startup mode)
   or both TLVs have the S flag clear (neither router is in startup
   mode), then the router with the numerically smaller Router-
   Fingerprint MUST generate a new System ID and restart the protocol.

   Fingerprint comparison is performed octet by octet starting from the
   first received octet until a difference is detected.  If the
   fingerprints have different lengths and all octets up to the shortest
   length are identical, then the fingerprint with smaller length is
   considered smaller on the whole.

   If the fingerprints are identical in both content and length (and the
   state of the S flag is identical), and the duplication is detected in
   hellos, then both routers MUST generate a new System ID and restart
   the protocol.

   If fingerprints are identical in both content and length, and the
   duplication is detected in LSP #0, then the procedures defined in
   Section 3.4.6 MUST be followed.

3.4.5.  System ID and Router-Fingerprint Generation Considerations

   As specified in this document, there are two distinguishing items
   that need to be self-generated: the System ID and Router-Fingerprint.
   In a network device, normally there are some resources that can
   provide an extremely high probability of uniqueness (some examples
   listed below).  These resources can be used as seeds to derive
   identifiers:

   o  MAC address(es)

   o  Configured IP address(es)

   o  Hardware IDs (e.g., CPU ID)

   o  Device serial number(s)

   o  System clock at a certain, specific time

   o  Arbitrary received packet(s) on an interface(s)






Liu, et al.                  Standards Track                    [Page 9]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   This document recommends the use of an IEEE 802 48-bit MAC address
   associated with the router as the initial System ID.  This document
   does not specify a specific method to regenerate the System ID when
   duplication happens.

   This document also does not specify a method to generate the Router-
   Fingerprint.

   There is an important concern that the seeds listed above (except MAC
   address) might not be available in some small devices such as home
   routers.  This is because of hardware/software limitations and the
   lack of sufficient communication packets at the initial stage in home
   routers when doing IS-IS autoconfiguration.  In this case, this
   document suggests using the MAC address as the System ID and
   generating a pseudorandom number based on another seed (such as the
   memory address of a certain variable in the program) as the Router-
   Fingerprint.  The pseudorandom number might not have a very high
   probability of uniqueness in this solution but should be sufficient
   in home network scenarios.

   The considerations surrounding System ID stability described in
   Section 3.2 also need to be applied.

3.4.6.  Duplication of Both System ID and Router-Fingerprint

   As described above, the resources for generating a System ID /
   Router-Fingerprint might be very constrained during the initial
   stages.  Hence, the duplication of both System ID and Router-
   Fingerprint need to be considered.  In such a case, it is possible
   that a router will receive an LSP with a System ID and Router-
   Fingerprint identical to the local values, but the LSP is NOT
   identical to the locally generated copy, i.e., the sequence number is
   newer or the sequence number is the same, but the LSP has a valid
   checksum that does not match.  The term DD-LSP (Duplication Detection
   LSP) is used to describe such an LSP.

   In a benign case, this will occur if a router restarts and it
   receives copies of its own LSPs from its previous incarnation.  This
   benign case needs to be distinguished from the pathological case
   where there are two different routers with the same System ID and the
   same Router-Fingerprint.

   In the benign case, the restarting router will generate a new version
   of its own LSP with a higher sequence number and flood the new LSP
   version.  This will cause other routers in the network to update
   their LSP Database (LSPDB) and synchronization will be achieved.





Liu, et al.                  Standards Track                   [Page 10]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   In the pathological case, the generation of a new version of an LSP
   by one of the "twins" will cause the other twin to generate the same
   LSP with a higher sequence number -- and oscillation will continue
   without achieving LSPDB synchronization.

   Note that a comparison of the S flag in the Router-Fingerprint TLV
   cannot be performed, as in the benign case it is expected that the S
   flag will be clear.  Also note that the conditions for detecting a
   duplicate system ID will NOT be satisfied because both the System ID
   and the Router-Fingerprint will be identical.

   The following procedure is defined:

       DD-state is a boolean that indicates if a
         DD-LSP #0 has been received.
       DD-count is the count of the number of occurrences
         of reception of a DD-LSP.
       DD-timer is a timer associated with reception of
        DD-LSPs; the recommended value is 60 seconds.
       DD-max is the maximum number of DD-LSPs allowed
        to be received in DD-timer interval;
        the recommended value is 3.

   When a DD-LSP is received:

     If DD-state is FALSE:
       DD-state is set to TRUE.
       DD-timer is started.
       DD-count is initialized to 1.

     If DD-state is TRUE:
       DD-count is incremented.
       If DD-count is >= DD-max:
          The local system MUST generate a new System ID
           and Router-Fingerprint and restart the protocol.
          DD-state is (re)initialized to FALSE and
           DD-timer is canceled.

     If DD-timer expires:
       DD-state is set to FALSE.

   Note that to minimize the likelihood of duplication of both System ID
   and Router-Fingerprint reoccurring, routers SHOULD have more
   entropies available.  One simple way to achieve this is to add the
   LSP sequence number of the next LSP it will send to the Router-
   Fingerprint.





Liu, et al.                  Standards Track                   [Page 11]


RFC 8196                 IS-IS Autoconfiguration               July 2017


3.5.  Additional IS-IS TLVs Usage Guidelines

   This section describes the behavior of selected TLVs when used by a
   router supporting IS-IS autoconfiguration.

3.5.1.  Authentication TLV

   It is RECOMMENDED that IS-IS routers supporting this specification
   offer an option to explicitly configure a single password for HMAC-
   MD5 authentication as specified in [RFC5304].

3.5.2.  Metric Used in Reachability TLVs

   It is RECOMMENDED that IS-IS autoconfiguration routers use a high
   metric value (e.g., 100000) as default in order to allow manually
   configured adjacencies to be preferred over autoconfigured.

3.5.3.  Dynamic Name TLV

   IS-IS autoconfiguration routers MAY advertise their Dynamic Name TLV
   (TLV 137 [RFC5301]).  The hostname could be provisioned by an IT
   system or just use the name of vendor, device type, or serial number,
   etc.

   To guarantee the uniqueness of the hostname, the System ID SHOULD be
   appended as a suffix in the names.

4.  Security Considerations

   In the absence of cryptographic authentication, it is possible for an
   attacker to inject a PDU falsely indicating there is a duplicate
   system ID.  This may trigger automatic restart of the protocol using
   the duplicate-id resolution procedures defined in this document.

   Note that the use of authentication is incompatible with
   autoconfiguration as it requires some manual configuration.

   For wired deployment, the wired connection itself could be considered
   as an implicit authentication in that unwanted routers are usually
   not able to connect (i.e., there is some kind of physical security in
   place preventing the connection of rogue devices); for wireless
   deployment, the authentication could be achieved at the lower
   wireless link layer.








Liu, et al.                  Standards Track                   [Page 12]


RFC 8196                 IS-IS Autoconfiguration               July 2017


5.  IANA Considerations

   This document details a new IS-IS TLV reflected in the "IS-IS TLV
   Codepoints" registry:

   Value  Name                             IIH LSP SNP Purge
   ----  ------------                      --- --- --- -----
   15    Router-Fingerprint                 Y   Y   N    Y

6.  References

6.1.  Normative References

   [ISO_IEC10589]
              International Organization for Standardization,
              "Information technology -- Telecommunications and
              information exchange between systems -- Intermediate
              System to Intermediate System intra-domain routeing
              information exchange protocol for use in conjunction with
              the protocol for providing the connectionless-mode network
              service (ISO 8473)", ISO/IEC 10589:2002, Second Edition,
              November 2002.

   [RFC1195]  Callon, R., "Use of OSI IS-IS for routing in TCP/IP and
              dual environments", RFC 1195, DOI 10.17487/RFC1195,
              December 1990, <http://www.rfc-editor.org/info/rfc1195>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC5301]  McPherson, D. and N. Shen, "Dynamic Hostname Exchange
              Mechanism for IS-IS", RFC 5301, DOI 10.17487/RFC5301,
              October 2008, <http://www.rfc-editor.org/info/rfc5301>.

   [RFC5304]  Li, T. and R. Atkinson, "IS-IS Cryptographic
              Authentication", RFC 5304, DOI 10.17487/RFC5304, October
              2008, <http://www.rfc-editor.org/info/rfc5304>.

   [RFC5305]  Li, T. and H. Smit, "IS-IS Extensions for Traffic
              Engineering", RFC 5305, DOI 10.17487/RFC5305, October
              2008, <http://www.rfc-editor.org/info/rfc5305>.

   [RFC5308]  Hopps, C., "Routing IPv6 with IS-IS", RFC 5308,
              DOI 10.17487/RFC5308, October 2008,
              <http://www.rfc-editor.org/info/rfc5308>.




Liu, et al.                  Standards Track                   [Page 13]


RFC 8196                 IS-IS Autoconfiguration               July 2017


   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <http://www.rfc-editor.org/info/rfc8174>.

6.2.  Informative References

   [RFC7503]  Lindem, A. and J. Arkko, "OSPFv3 Autoconfiguration",
              RFC 7503, DOI 10.17487/RFC7503, April 2015,
              <http://www.rfc-editor.org/info/rfc7503>.

Acknowledgements

   This document was heavily inspired by [RFC7503].

   Martin Winter, Christian Franke, and David Lamparter gave essential
   feedback to improve the technical design based on their
   implementation experience.

   Many useful comments were made by Acee Lindem, Karsten Thomann,
   Hannes Gredler, Peter Lothberg, Uma Chundury, Qin Wu, Sheng Jiang,
   and Nan Wu, etc.






























Liu, et al.                  Standards Track                   [Page 14]


RFC 8196                 IS-IS Autoconfiguration               July 2017


Authors' Addresses

   Bing Liu (editor)
   Huawei Technologies
   Q10, Huawei Campus, No.156 Beiqing Road
   Hai-Dian District, Beijing, 100095
   P.R. China

   Email: leo.liubing@huawei.com


   Les Ginsberg
   Cisco Systems
   821 Alder Drive
   Milpitas  CA 95035
   United States of America

   Email: ginsberg@cisco.com


   Bruno Decraene
   Orange
   France

   Email: bruno.decraene@orange.com


   Ian Farrer
   Deutsche Telekom AG
   Bonn
   Germany

   Email: ian.farrer@telekom.de


   Mikael Abrahamsson
   T-Systems
   Stockholm
   Sweden

   Email: mikael.abrahamsson@t-systems.se










Liu, et al.                  Standards Track                   [Page 15]